Tiling to existing vinyl floor coverings

PREPARATION
The existing vinyl must be in good condition, clean and dry. N.B. cushion floor coverings are not suitable to receive a ceramic tile finish and must be removed (When fixing onto vinyl adhesive residues refer to the Norcros How to sheet for ‘Fixing to Bitumen Surfaces’. Clean and degrease the vinyl. Any loose tiles should be removed, together with any adhesive residues, dirt and dust etc. Make good the area.

Standard Domestic Vinyl Tiles & Coverings
Brush apply a neat coat of Norcros Prime Bond to the existing vinyl and allow to dry.

Heavy Duty/ Commercial Vinyls
Brush apply a a slurry bonding coat consisting of 2 parts of cement-based adhesive to 1 part Norcros Prime Bond to the existing vinyl & allow to dry.

SETTING OUT
The general rule is to work from the centre outwards. Measure the width and length of the floor and draw a cross in the centre. From the central cross lay out the dry tiles allowing a 3mm wide gap between the tiles to allow for movement stresses within the floor during service. These gaps will be filled with grout once the tiles have been fixed and the adhesive dried. Make sure there are no awkward cuts, some adjustment may be necessary. Always be aware of how the floor will look when you enter the room.

To counteract movement stresses, which can result in tiles cracking and/or debonding. A movement joint should be provided around the perimeter of the room. A gap no less than 6mm wide and 6mm deep or the depth of the tile should be left at the junction between the walls and the floor. This should be filled with silicone sealant at the end of the job, or if being covered with skirting boards or kitchen units etc. may be left open. In large floor areas, intermediate movement joints should be provided at 8 to 10 metre intervals in both directions.

FIXING
Fix tiles in a polymer modified cement-based adhesive such as Norcros Rapid Porcelain Tile Adhesive Grey, Norcros Rapid Porcelain & Stone Adhesive White, Norcros Rapid Porcelain S1 or Norcros Thick Bed Stone & Porcelain Adhesive. Mix as per the instructions on the bag.

Rapid Porcelain Tile AdhesiveRapid Porcelain and Stone AdhesiveRapid Porcelain and Stone S1 Tile AdhesiveRapid Porcelain S1 Tile AdhesiveThick Bed Porcelain and Stone AdhesiveThick Bed Porcelain and Stone Adhesive

APPLICATION
Using a suitable notched floor trowel held at a 45o angle, spread the adhesive onto the floor to form parallel ribs into which the tiles should be pushed with a firm twisting action, this will collapse the ribs of adhesive and produce a 3-4mm solid bed of adhesive beneath the tiles. Work in small areas and discard any adhesive that begins to dry or ‘skin over’. Tiles with deeply keyed back pro-files may need to back buttered. Every so often lift a tile to check that it is in full contact with the adhesive and that no voids are left in the adhesive bed. Wipe off any adhesive residues from the surface of the tiles using a damp sponge before the adhesive sets. Remove deposits of adhesive which may build up in the gaps between the tiles. DO NOT WALK ON THE TILES FOR AT LEAST 2-3 HOURS, or until the adhesive has set.

CUTTING TILES
Floor tiles, especially natural stone and porcelain can be difficult to cut and good quality tools are required. These can bought or in some instances hired. A slide cutter and nippers are essential, however an electric wet cutter will make the job easier. For intricate cuts a cardboard template will help to achieve more accurate results.

GROUTING
Allow the adhesive to dry.
Use either Norcros Floor & Wall Tile Grout, Norcros Flexible Floor & Wall Tile Grout or Norcros 4 into 1 Grout. Clean out any dust, dirt and adhesive from between the tiles and make sure that the joints are dry.

Approximately 4-5 parts grout powder should be added to 1 part water, ensuring that the powder is added to the liquid to prevent the product from flash setting. Manually mix the grout to reduce the amount of air incorporated into the mix.

Holding a soft rubber grout float at 45o, sweep the mixed grout diagonally across the tiles, ensuring that the grout is pushed fully into the joints. Clean off as much grout from the surface of the tiles as possible and allow the grout to become touch dry. Clean off the grout residues with a damp sponge wiped diagonally across the tiles. Allow the tiles to dry and buff the surface with a dry cloth. Any stubborn residues may be cleaned off with washing up detergent mixed with warm water within 24 hours of grouting.

N.B. Before grouting commences trial a small inconspicuous area to check that the grout does not stain the tiles. If there is any risk of staining, the tiles should be fully sealed using a proprietary sealer before grouting begins.

Other How To's

How To

Tiling to cement: sand render walls

PREPARATION The render must be a minimum of 2 weeks old to enable movement caused by drying shrinkage to have taken place. It must be clean, dry and free from dust, laitance or any other contaminants which may act as a release agent, preventing the adhesive from bonding to the render. If the render is […]

How To

Tiling to plasterboard walls

PREPARATION Plasterboard should be dry, securely fixed and rigid with no protruding fixings with the face to receive decorative finishes exposed. It should be a minimum 12.5mm thick when fixed to timber framing or battening and fixed in accordance with the manufacturers recommendations. The maximum weight of tiling which plasterboard is able to support is […]

Technical Support

For technical information about Norcros Adhesive products please call:

01782 524140

Technical Support

Technical Support

For technical information about Norcros Adhesive products please call: 01782 524140

tick

How to videos

ViewUse our ‘How To’ guides to help you perfect your tiling job.